- #Cleanflight firmware upgrade mac update#
- #Cleanflight firmware upgrade mac manual#
added support for the Redpine RC protocol on devices with an SPI connected CC2500 chip (FrSky SPI).Ĭhanges from the previous Release Candidate:.added support for FrSkyOSD OSD devices.
added support for enhanced OSD / CMS devices, made it possible to support highligting of text or symbols. added the option to display the OSD logo on arming. Added level race mode ('NFE race mode' in Silverware). added compensation for sagging battery voltage, resulting in more consistent throttle / PID behaviour over for the entire flight time. added new selectable ACTUAL and QUICK rates models. completely reworked the gyro loop, improved performance and made it always run at the native speed of the gyro. the name CLI command has been removed. If you want to use stick arming (at your own risk), it has to be enabled by setting enable_stick_arming to on since stick arming is not recommended for multirotor craft because it can lead to accidental disarms, it has been disabled by default. This means that if a custom setting for osd_rssi_dbm_alarm is used, this will have to be changed to be the inversion of its previous value (e.g. the way that the 'RSSI dBm' value is tracked in the firmware has changed to use actual dBM value in a range of -130 to 0, instead of the previous version's 130 to 0 range. If you are using the virtual current meter device, make sure to calibrate it again after updating the firmware to make sure the calibration is still correct This means that this value has things like throttle limiting and throttle boost applied, resulting in more accurate prediction of current and consumption. the calculation for the virtual current meter device has been changed to be based on the throttle value used in the mixer, instead of the throttle channel RC input. Arming will be disabled and a warning displayed in configurator until the accelerometer has been calibrated This is to prevent situations arising where the craft may try to self-level with an uncalibrated accelerometer, leading to unexpected or dangerous results. accelerometer calibration is now required before arming is allowed if any feature is enabled that requires the accelerometer. #Cleanflight firmware upgrade mac manual#
Manual configuration of the yaw spin threshold is still possible This new mode is the default for yaw spin threshold, since it provides a setting that is safe to use for most users.
the threshold for activation of the yaw spin recovery feature has had an automatic mode added - this mode sets the threshold to a value that is based on the currently configured maximum yaw rate, with a buffer added on top of it. In particular, this means that with Dshot300 and bidirectional Dshot, the maximum PID loop speed is 4 kHz when enabling bidirectional Dshot, the maximum possible PID loop speed for Dshot protocols will be reduced by half to accommodate for the time taken by the ESC to send the RPM data packet to the flight controller. Arming will be disabled and a warning displayed in configurator until a motor output protocol has been selected But this also removed the limitation on the maximum possible PID loop speed imposed by the pre-selected legacy protocol (OneShot125) in earlier versions, resulting in the maximum possible PID loop speed for each MCU type being pre-selected. This means that the correct motor protocol has to be selected before the craft can be armed. after installing new firmware or resetting the configuration, the motor output protocol selected by default is now 'disabled'. Some defaults have been changed, and some parameters are used in different ways, so previous tuning settings will not work well with Cleanflight 4.2 please do not paste tuning configurations from previous versions of the firmware. This includes changes to go with Cleanflight 4.2 (installation instructions here) 
version 1.5.0 of the Cleanflight TX lua scripts will be released soon.if you are using the Blackbox Explorer, there will be an updated version 3.5.0 to go with Cleanflight 4.2 (installation instructions here).
#Cleanflight firmware upgrade mac update#
For this reason it is important that you update to the version 2.6.0 or newer of Cleanflight Configurator (installation instructions here) in order to get the latest version of your targets installed The latest release of Cleanflight Configurator, 2.6.0, contains the changes necessary to support this.
Cleanflight 4.2 brings some changes to how targets are downloaded and installed. Please use it with caution and report back any issues at. It is intended for testing, and some things still need fixing and fine tuning.
0 kommentar(er)
